關于光伏墩模具的介紹生產出來的光伏墩一般都是采用預制的生產方式，這是一種比較常用的生產方式，因為這樣的生產出來的產品的質量是比較高的，而且將生產出來的光伏墩運輸到施工的現場能夠加快工人施工的速度，減少施工的時間，這樣對當地的交通的影響也是比較小的。這種模具在進行制作的時候是進行的操作是比較細致的，所以生產出來的光伏墩的表面是非常光滑的，而且使用的年限也是比較長的。我們的這種光伏墩主要就是應用在光伏發電設施的建設之上，發揮的作用是非常大的，這些工程對光伏墩的質量要求是比較高的，所以他們使用的都是使用預制的光伏墩。我們生產這種光伏墩一般都會使用光伏墩模具，他與其他的模具的使用方法是相同的。如果應用的建設工程不同那么需要的光伏墩模具的規格大小也是有所不同的，在制作之前要將注塑機的胎具更換成我們所需要的尺寸大小，我們制作完成的模具不可以直接賣給客戶，需要對其的質量進行檢測，這樣才能保證我們的口碑。
About the introduction of PV pier mold, the PV pier produced is generally prefabricated, which is a common production method, because the quality of the products produced is relatively high, and transporting the PV pier to the construction site can speed up the construction speed of workers and reduce the construction time, In this way, the impact on local traffic is relatively small. The operation of this kind of mold is relatively detailed when making, so the surface of the produced photovoltaic pier is very smooth, and the service life is relatively long. Our photovoltaic piers are mainly used in the construction of photovoltaic power generation facilities and play a very important role. These projects have relatively high quality requirements for photovoltaic piers, so they use prefabricated photovoltaic piers. We generally use the photovoltaic pier mold in the production of this kind of photovoltaic pier, and the use method is the same as that of other molds. If the applied construction projects are different, the specifications and sizes of the PV pier molds required are also different. Before production, the molds of the injection molding machine should be replaced with the sizes we need. The molds we have made can not be directly sold to customers. Their quality needs to be tested in order to ensure our reputation.
光伏墩模具都是在預制廠實現生產的，預制廠是分為幾大場地的，有生產預制件的場地、存放預制件的場地和儲存模具的場地，下面簡單的介紹一下模具的操作步驟�，F澆的震動平臺準備出來的，將上面雜物清理干凈，然后將模具擺放到平臺上的同時進行刷油，模具上需要刷油的位置不僅是內底面，內側壁上也要刷刷上油，從模具的上下面的尺寸上來看是有錐度的，這是所有塑料模具都需要的考慮到的一點�？梢允褂描F鍬或是平鏟子將水泥裝入六角板模具當中，將振動平臺上所有模具灌滿后再開啟震動平臺，因為劉防撞的容積是比較小的，所以震動幾十秒之后就可以了。光伏基座模具的制作以都設計成帶有錐度的樣式主要是為了方便脫模，這樣在等模具中的水泥完全風干后在將模具倒扣的時候里邊的六角板才更容易從與模具脫離開來，而刷油步驟也是為了減小水泥和模具的粘連度，增強光滑性，但是盡量不要使用的廢機油，廢機油可能會導致預制件的顏色出現變化。
PV pier molds are produced in the prefabrication plant. The prefabrication plant is divided into several sites, including the site for producing prefabricated parts, the site for storing prefabricated parts and the site for storing molds. The following is a brief introduction to the operation steps of molds. When the cast-in-situ vibration platform is prepared, clean up the sundries on it, and then brush the oil while placing the mold on the platform. The position on the mold that needs to be painted is not only the inner bottom surface, but also the inner wall. From the dimension of the upper and lower parts of the mold, there is a taper, which should be considered for all plastic molds. You can use the spade or the flat shovel to load the cement into the six corner plate mold, then fill all the mold on the vibrating platform and then open the vibrating platform, because the volume of the collision avoidance is relatively small, so it can be vibrated after dozens of seconds. The PV base molds are designed with taper to facilitate demoulding, so that when the cement in the mold is completely air dried and the mold is buckled, the inner hexagonal plate can be more easily separated from the mold. The oil brushing step is also to reduce the adhesion between the cement and the mold and enhance the smoothness, but try not to use waste oil, Waste oil may cause the color of preforms to change.
打印